Surface free energy of CrNx films deposited using closed field unbalanced magnetron sputtering

CrN_x thin films have attracted much attention for semiconductor IC packaging molding dies and forming tools due to their excellent hardness, thermal stability and non-sticking properties (low surface free energy). However, few data has been published on the surface free energy (SFE) of CrN_x films at temperatures in the range 20-170 °C. In this study CrN_x thin films with CrN, Cr(N), Cr₂N (and mixture of these phases) were prepared using closed field unbalanced magnetron sputtering at a wide range of Cr⁺² emission intensity. The contact angles of water, di-iodomethane and ethylene glycol on the coated surfaces were measured at temperatures in the range 20-170 °C using a Dataphysics OCA-20 contact angle analyzer. The surface free energy of the CrN_x films and their components (e.g., dispersion, polar) were calculated using the Owens-Wendt geometric mean approach. The influences of CrN_x film surface roughness and microstructure on the surface free energy were investigated by atomic force microscopy (AFM) and X-ray diffraction (XRD), respectively. The experimental results showed that the lowest total SFE was obtained corresponding to CrN at temperature in 20 °C. This is lower than that of Cr(N), Cr₂N (and mixture of these phases). The total SFE, dispersive SFE and polar SFE of CrN_x films decreased with increasing surface temperature. The film roughness has an obvious effect on the SFE and there is tendency for the SFE to increase with increasing film surface roughness.     

Fluorescence anisotropy decay study of self-association of bacterial luciferase intermediates

The fluorescence dynamics parameters of the fluorescent transient flavin-luciferase species from the typesVibrio fischeri andPhotobacterium leiognathi are presented. The fluorescence anisotropy decay is a single exponential function for both types. The correlation time is 70 ns for theP. leiognathi fluorescent transient intermediate (2°C, aqueous buffer, pH 7.0), consistent with the rotational correlation time of the luciferase macromolecule (77 kD) to which the flavin fluorophore is rigidly attached. In contrast, for theV. fischeri species the observed correlation time for the anisotropy decay function is 133 ns. This suggests that protein self-association occurs in theV. fischeri case and this is confirmed by filtration, where the fluorescent transient fromV. fischeri does not pass through a 100,000 molecular weight cutoff membrane, whereas theP. leiognathi species does. The filtration method also demonstrates self-association in the luciferase peroxyflavin and photoflavin fromV. fischeri. A monomer-dimer equilibrium also explains the previously reported high correlation times for theV. harveyi luciferase-flavin species. It is proposed that the self-association competes with the lumazine protein interaction in the bioluminescence reaction.     

Regioselective construction of polysubstituted benzene ring from Baylis-Hillman adduct via [4+2] annulation strategy

A new and regioselective [4+2] benzannulation protocol toward polysubstituted benzenes was developed. Nitroalkane derivative, which was prepared from Baylis-Hillman adduct, served as the four-carbon unit and Michael acceptor as a two-carbon unit.     

An experimental and computational investigation of crack initiation and stable crack growth of ductile materials

Crack initiation and stable crack growth under monotonic loading in steels has been studied using an elastic-plastic finite element analysis. The fracture criterion used for crack initiation and stable crack growth was the critical strain energy density. In addition the shift core method for the analysis of crack extension was used. In the shift core modelling method, crack advance is simulated by moving the coordinates of the core region which surrounds the crack tip, to obtain the stiffness reduction. Simultaneously the core itself geometrically undergoes a simple rigid-body motion or translation during the crack extension. The analytically calculated and experimentally measured load for crack initiation and the subsequent stable crack growth agreed well.     

Towards understanding the increase in strength of thermotropic polyesters with heat treatment

Thermotropic copolyester fibers of oxynaphthoate and oxybenzoate have been subjected to conditions that promote solid-state polymerization as well as annealing. The annealing process causes the crystals to perfect with a simultaneous increase in heat of fusion and melting temperature. Solid-state polymerization, a reaction rate-controlled process, causes the polymer viscosity average molecular weight to increase by chain extension from about 14,000 g/mole to more than 87,000 g/mole with a simultaneous impressive increase in tenacity from about 10 g/d (1.2 GPa) to almost 30 g/d (3.7 GPa). To understand the changes in mechanical properties, we have modeled the fiber structure as short rod-like molecules poorly bonded to a continuous matrix of parallel molecules. Lengthening of the reinforcing molecules facilitates better transfer of load from matrix to molecules, resulting in higher tenacity fibers. © 1994 John Wiley & Sons, Inc.     

Synthesis and characterization of liquid crystalline side‐chain block copolymers containing luminescent 4,4′‐bis(biphenyl)fluorene pendants

A series of new liquid crystalline homopolymers, copolymers, and block copolymers were polymerized from styrene‐macroinitiator ( SMi ) and methacrylates with pendent 4,4′‐bis(biphenyl)fluorene ( M1 ) and biphenyl‐4‐ylfluorene ( M2 ) groups through atom transfer radical polymerization (ATRP). The number‐average molecular weights (Mn) of polymers P1 ‐ P4 were 10,007, 14,852, 6,275, and 10,463 g mol^?1 with polydispersity indices values of 1.21, 1.15, 1.31, and 1.22, respectively. All polymers exhibit the nematic phase. The thermal, mesogenic, and photoluminescent properties of all polymers were investigated. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4564–4572, 2007     

Metallothionein as a biomarker for mercury in tissues of rat fed orally with cinnabar

Cinnabar, as one of the most widely used mineral drugs in traditional Chinese medicines, has been proven to have prominent curative effects in clinical use for more than 2000 years. But the safety and toxicity of the drug has been under constant debate in clinic usage. Metallothionein (MT) contains about 30% of cysteine in the molecule, and plays an important detoxification role against heavy metals. In this study, it was used as a biomarker to assess mercurial accumulation in rats fed orally with cinnabar. After feeding rats with cinnabar by gastric gavage at different dosages and at different times, the distribution of heavy metals (including mercury, copper and zinc) and MT was investigated among rat tissues, including liver, kidney, heart, brain, testis and blood. Metals and MT determinations were carried out using inductively coupled plasma mass spectrometry (ICP‐MS) and a modified mercury saturation assay technique respectively. The results indicated that mercury was easily accumulated in the tissues of rats exposed to cinnabar, especially in kidney. For example: at a feeding dosage of 5 g kg^?1 (bw) for 4 weeks, the mercury concentrations in kidney were 13, 8.7, 21.6 and 26 times those in liver, testis, brain and heart respectively; and at 2.5 g kg^?1 (bw) for 2 weeks, the mercury concentrations in kidney were 21, 2.1, 3 and 21 times those in liver, testis, brain and heart respectively. In addition, mercury in kidney and liver of all cinnabar groups was significantly higher than that of the control group (P < 0.01). A high positive correlation observed between MT concentrations and mercury levels in both liver and kidney (R² = 0.9299, P < 0.02 for liver; R² = 0.9923, P < 0.0008 for kidney) indicated that MT could be used as a biomarker for mercury in tissues. Copyright © 2004 John Wiley & Sons, Ltd.     

Operator‐splitting method for the analysis of cavitation in liquid‐lubricated herringbone grooved journal bearings

This paper presents an operator‐splitting method (OSM) for the solution of the universal Reynolds equation. Jakobsson–Floberg–Olsson (JFO) pressure conditions are used to study cavitation in liquid‐lubricated journal bearings. The shear flow component of the oil film is first solved by a modified upwind finite difference method. The solution of the pressure gradient flow component is computed by the Galerkin finite element method. Present OSM solutions for slider bearings are in good agreement with available analytical and experimental results. OSM is then applied to herringbone grooved journal bearings. The film pressure, cavitation areas, load capacity and attitude angle are obtained with JFO pressure conditions. The calculated load capacities are in agreement with available experimental data. However, a detailed comparison of the present results with those predicted using Reynolds pressure conditions shows some differences. The numerical results showed that the load capacity and the critical mass of the journal (linear stability indicator) are higher and the attitude angle is lower than those predicted by Reynolds pressure conditions for cases of high eccentricities. Copyright © 2004 John Wiley & Sons, Ltd.